GNR射频指标发射部分释义
2023-04-08 来源:文库网
GNR射频指标发射部分释义
本文核心词:5G NR射频指标发射部分释义
5G频段分两部分:FR1和FR2
5G频段FR1和FR2
下面是FR1也就是 sub 6G的频段表:
sub 6G频段
国内运营商移动部署的5G频段是n41和n79,联通和电信部署的频段都是n78,具体频率范围如下:
中国移动:n41:2515~2675MHz,n79:4800~4900MHz;
中国电信:n78:3400~3500MHz;
中国联通:n78:3500~3600MHz;
3GPP中关于5G FR1(sub 6G)的射频指标要求都在38.101中,其中38.101-1和38.101-2分别定义的是SA架构下FR1(sub 6G)和FR1(毫米波)下的射频指标要求,38.101-3是ENDC 和5G CA组合下的5G射频指标要求,ENDC就是我们现阶段国内运营商正在推行的NSA架构。因为NSA架构属于过渡阶段,运营商重点部署的是SA架构,因此本文重点讲述SA架构下5G的射频指标,也就是38.101-1。
3GPP相关文档下载地址:
发射指标:
6 发射特性
6.2 Transmitter power发射功率;
6. 2.1 UE maximum output power最大发射功率
以上测试取样周期至少为1个子帧,1ms,除非特别说明,对各自支持的所有带宽都有效
不同class对应的最大发射功率表
6. 2.2 UE maximum output power reduction最大发射功率回退
5G NR允许终端在特定的调制方式、特定的RB分配机制下,适当回退最大发射功率,以适应高阶调制带来的发射指标超标或者占用带宽超标的问题;
5G NR功率回退机制
6. 2.3 UE additional maximum output power reduction额外最大发射功率回退
额外最大功率回退是网络端基于杂散的额外要求而设定的,额外最大功率回退值和最大功率回退值不能重复叠加,取最大值做回退,
特定频段特定RB信令连接的最大功率回退
6.3 Output power dynamics输出功率动态范围
6.3.1 Minimum output power最小输出功率
The minimum controlled output power of the UE is defined as the power in the channel bandwidth for all transmit bandwidth configurations (resource blocks), when the power is set to a minimum value.
The minimum output power is defined as the mean power in at least one sub-frame 1 ms. The minimum output power shall not exceed the values specified in Table 6.3.1-1.
最小发射功率的概念我们不应该陌生,无论是Wcdma还是LTE都有这项指标要求,在最小1个子帧(1ms)的测试周期内,所有带宽和RB配置下,都应该满足最小发射功率小于某个规定的大小。这个指标的含义是手机终端和基站足够近的场景下,手机应该能够响应基站的要求,发射足够小的功率出来,从而可以最大可能的长时间上网。
最小发射功率
6.3.2 Transmit OFF power发射关功率
Transmit OFF power is defined as the mean power in the channel bandwidth when the transmitter is OFF. The transmitter is considered OFF when the UE is not allowed to transmit on any of its ports..
The transmit OFF power is defined as the mean power in a duration of at least one sub-frame (1 ms) excluding any transient periods. The transmit OFF power shall not exceed the values specified in Table 6.3.2-1.发射关功率的概念和LTE完全相同,网络要求终端关闭发射的时候,射频收发器的发射电路和PA都关闭,此时在射频口测试到的功率既是发射关功率,测试周期也是至少1个子帧(1ms)。这个指标反映的是终端保持安静的能力,主要是测试射频发射前端电路是否彻底关闭,以及是否有自激或者接收电路的锁相环电路有无泄露等。